Hitec Optic 6 Sport 2.4 Manuel d'utilisateur

6CH 2.4GHz DIGITAL COMPUTER RADIO SYSTEM SYSTEM2.4Function Assignable SwitchesEasy to Read LCD ScreenBulit-in Hitec AFHSS 2.4GHz System INSTRUCTION M

Page 17 Page 18Optima Series Receiver Features and setupSet-up and Use of the Hitec 2.4GHz System1Sec.3Sec.3Sec.Turn on transmitter, then the receive

Page 19 Page 20Optima Series Receiver Features and setupOptima Series Receiver Features and setupSet-up and Use of the Hitec 2.4GHz SystemAlways do a

Page 21 Page 22Telemetry SystemSPC (Supplementary Power Connection) SystemOptima Series Receiver FeaturesOptima Series Receiver Features and setupIt i

Page 23 Page 24Startup ScreenFAIL-SAFE and Hold ModeReceiver-Servo Connection ListTransmitter Displays and MessagesThe table below shows where the air

Page 25 Page 261. Select a model slot:4. Configure the countdown timer:2. Select the Model type programming baseline:3. Heli Swash Plate:Before you tu

Page 27 Page 28Model Setup Menu Programming for Powered Airplanes (ACRO) ACRO Functions Map EPA End Point Adjust (Servo travel) 27 D/R Dual Rate

Page 29 Page 30EPA (End Point Adjustment)Setting up End Points Elevator End PointsThrottle End Points1) To set the UP elevator motion, press on the R

Page 31 Page 32EPA (End Point Adjustment)EXP (Exponential)Setting Up Exponential1) Push the CURSOR buttons repeatedly until the channel "1"

Page 33 Page 34S. TRM (Sub Trim)Set Up a Throttle Rudder MixP. MIX (Programmable Mix)In this screen you can activate the ability of the Optic 6 Sport

Page 35 Page 36ELVN (Elevon mix)Setting up elevonsFLPN (Flaperon)Setting up flaperons1) Activate the program by pushing both DATA buttons-the "I

Page 1 Page 2The Optic 6 Sport 2.4 advanced features include:Model Memory: The computer's memory is capable of storing all the necessary trim set

Page 37 Page 38A  R (Aileron-Rudder Mix)Setting up a Rudder-to-Aileron MixCUT (Engine Cut Function) CUT (Engine Cut Function)CAMB (Wing Camber)1)

Page 39 Page 40FLT. C (Flight Conditions)Setting up Flight Condition Modes FLT. C (Flight Conditions) FLT. C (Flight Conditions)IMPORTANT NOTE :

Page 41 Page 42This figure shows the assignments for a Mode 2 system as supplied by the factory. Note that some of the functions will not operate u

Page 43 Page 44ADIF (Aileron Differential)Activating FlaperonsCreating Aileron DifferentialSTCK (Throttle Stick or Switch) If your glider uses an e

Page 45 Page 46Setting Up CROWCAMB (Wing Camber) Setting Up Flight Mode Wing Camber and Elevator CompensationCROW (Glide-Path and Airspeed Control)C

Page 47 Page 48Select the Model Type Baseline:Heli Swash Plate:Optic 6 Sport Heli In-Flight Controls This section covers the Optic 6 Sport programmin

Page 49 Page 50The Two Common Types of Power: Electric and GlowModel Setup Menu Programming for HelicopterThis section describes how to use the Optic

Page 51 Page 52P. CV (Pitch Curve)Setting Up The Throttle CurveLike the throttle curve described previously, pitch curves are tied to the position of

Page 53 Page 54HOLD (Throttle Hold)RVMX (Revolution Mix)The revolution mixing function mixes pitch commands to the tail rotor in order to suppress

Page 55 Page 56Your Optic 6 Sport 2.4’s system's HELI menu provides three flight modes in addition to the normal one (NOR). Within each conditio

Page 3 Page 4Vibration and WaterMountingHitec AFHSS 2.4GHz TechnologyEquipment MountingWhen you mount each servo, use the supplied rubber grommets and

Page 56 Page 57OPTIC 6 SPORT HELI DATA SHEETOPTIC 6 SPORT GLID DATA SHEET% % %% %%%CH1 CH2 CH3 CH4 CH5 CH6 MODEL TYPE : GLID SFT : N , P

Page 5 Page 6ConnectorsBe careful if you do choose to use a field charger on your batteries. A fast-charger may overcharge the batteries, causing ove

Page 7 Page 8Stick Lever Tension Adjustment Change to ‘Mode 1’ Configuration- Before you fly, perform a range check to confirm your radio system is r

Page 10 Page 11This pair of buttons has three basic functions: they get you into the initial setup menu when you hold both EDIT buttons down and then

Page 11 Page 12Right-hand joystickLeft-hand joystick"SW-1" switch"SW-2" switchOptic 6 Sport 2.4GHz Transmitter FeaturesDepending o

Page 13 Page 141. Function Button Used for Linking(ID-Setting) the receiver to a module, entering Fail-Safe / Hold mode setup function.2. Dual LED

Page 15 Page 16ID-Setup A.K.A, Link or BindOptima Series Receiver Features and setupSet-up and Use of the Hitec 2.4GHz SystemNormal Mode / Scan Mode C